锰离子氧化沉淀法实现锂离子电池LiNi0.8Co0.05Mn0.15O2材料的回收和利用

以浓盐酸为浸出剂,以NaOH和NH₄HCO₃为沉淀剂,利用Mn²⁺在碱性条件下的氧化反应改变离子的沉淀次序进而分步回收的方案,探究了浓盐酸酸浸处理三元正极材料LiNi_0.8Co_0.05Mn_0.15O₂的最佳条件。在分步沉淀过程中,Mn²⁺被氧化为不溶于非还原性酸的MnO （OH）₂,并在酸性条件下回收。Ni、Co则在碱性条件下利用NaOH回收,而Li则利用NH₄HCO₃回收。该方法中Mn的回收率达到85.1%,产品纯度达到98.6%; Li的回收率达到95.0%,产品纯度达到99.3%。由回收材料重新合成的三元正极组装的软包电池的首圈放电比容量达到了175 mAh·g^-1,可以以超过99.5%的库仑效率稳定循环50圈。     

CATALYTIC WET PEROXIDE OXIDATION OF HYDROQUINONE WITH Co（II）/ACTIVE CARBON CATALYST LOADED IN STATIC BED

Catalysts based on Co（II） supported on active carbon were prepared and loaded in static bed. The hydroquinone would be degraded completely after treated by Catalytic wet peroxide oxidation method with Co（II）/active carbon catalyst. After activate treatment, the active carbon was immerged in cobaltous nitrate solution, then put into a drying oven, Co（II） could be loaded on the micro-surface of carbon. Taking the static bed as the equipment, the absorption of active carbon and catalysis of Co（II） was used to reduce activation energy of hydroquinone. Thus hydroquinone could be drastically degraded and the effluent can be drained under the standard. Referring to Fenton reaction mechanism, experiment had been done to study the heterogeneous catalyzed oxidation mechanism of Co（II）. The degradation rate of hydroquinone effluent could be achieved to 92% when treated in four columns at H2O2 concentration 10%, reaction temperature 40 ℃, pH 5 and reaction time 2.5h.     

蒸发器出口状态热式测量的实验研究

根据热式感应原理,专门设计热式感应传感器,用于测量蒸汽压缩制冷循环中干式蒸发器出口的气液两相流动状态;热式感应传感器的测量数据与蒸发器出口流型、过热度等参数的综合比较分析表明:热式感应传感器可以辨识出蒸发器出口过热蒸汽、雾状流和二者交替三种流动状态.同时,实验数据表明蒸发器出口处于过热蒸汽、雾状流二者交替的过渡区时其换热效率最佳,因此热式感应传感器可以用于作为膨胀阀-干式蒸发器调节回路的反馈信号.应用热式感应传感器对蒸发器出口状态的随机性和周期性波动的测量证明:热式感应传感器动态性能良好,可以实时反映蒸发器出口状态变化.     

Acrylic fibers processing with ionic liquid as solvent

Ionic liquid, 1‐butyl‐3‐methylimidazolium chloride ([BMIM]Cl), was used as solvent for the polymerization of acrylonitrile (AN) and the resulting polymer solution was directly applied for spinning to produce polyacrylonitrile (PAN) fiber for the first time. Acrylic polymers with high content of AN, large molecular weight, and low polydispersity index (PDI) were prepared. The PAN macromolecules have little degradation during dissolution of PAN in [BMIM]Cl, which is completely different from the dissolution of biopolymers such as cellulose in ionic liquids. The PAN fiber with round profile and good mechanical properties was successfully spun from the PAN/[BMIM]Cl solution using dry–jet wet spinning technology. It suggests that an environmental friendly process for the acrylic fiber would be developed and the high performance PAN fiber would be obtained when the spinning conditions are optimized further. Copyright © 2008 John Wiley & Sons, Ltd.     

Improvement in a-plane GaN crystalline quality using wet etching method

Nonpolar （1120） GaN films are grown on the etched a-plane GaN substrates via metalorganic vapor phase epitaxy. High-resolution X-ray diffraction analysis shows great decreases in the full width at half maximum of the samples grown on etched substrates compared with those of the sample without etching, both on-axis and off-axis, indicating the reduced dislocation densities and improved crystalline quality of these samples. The spatial mapping of the E2 （high） phonon mode demonstrates the smaller line width with a black background in the wing region, which testifies the reduced dislocation densities and enhanced crystalline quality of the epitaxial lateral overgrowth areas. Raman scattering spectra of the E2 （high） peaks exhibit in-plane compressive stress for all the overgrowth samples, and the E2 （high） peaks of samples grown on etched substrates shift toward the lower frequency range, indicating the relaxations of in-plane stress in these GaN films. Furthermore, room temperature photoluminescence measurement demonstrates a significant decrease in the yellow-band emission intensity of a-plane GaN grown on etched templates, which also illustrates the better optical properties of these samples.     

湿颗粒堆力学特性的离散元法模拟研究

利用基于线性黏聚接触模型的离散元法对不同颗粒系统的堆积过程进行了数值模拟研究,分析了颗粒形状和湿颗粒间液桥力对颗粒堆积形态的影响机理,获得了球形和块状湿颗粒堆基底表面所受的法向力以及堆中颗粒间的法向力和切向力"中心凹陷"式的分布规律,讨论了颗粒形状和黏聚能量密度对基底表面作用力和颗粒间作用力的影响.研究结果表明,颗粒形状和液桥力对颗粒堆的堆积形态具有显著的影响.堆积角随着黏聚能量密度的增加而增大,并且相同条件下的块状颗粒堆积角大于球形颗粒.颗粒形状和黏聚能量密度对基底表面所受作用力和堆中颗粒间的作用力变化及最大幅值均有影响作用.当黏聚能量密度值逐渐增大时,颗粒堆的作用力最大幅值均逐渐增大,并且块状颗粒堆的作用力最大幅值大于球形颗粒堆.当黏聚能量密度值过大时,颗粒堆力学特性更加复杂,液桥力对颗粒堆积特性的影响作用大于颗粒形状的影响.     

湿消解-电感耦合等离子体发射光谱法测定药用胶囊中的铬含量

以硝酸作为消解液,采用湿消解-电感耦合等离子体发射光谱法(ICP-AES)测定药用胶囊中的铬含量.在0～80 ng/mL范围内,铬的浓度与发射光强度呈良好的线性关系,相关系数r=0.999 98,检出限为1.42 ng/mL.对3个浓度水平的铬标准溶液进行平行测定,测定结果的相对标准偏差为1.43％～1.79％(n=6),加标回收率为93.1％ ～110.0％.该方法可以用于药用胶囊中铬的日常检测.     

化学液相汽化沉积法制备炭/炭复合材料的湿态摩擦磨损性能研究

采用化学液相汽化沉积工艺制备炭/炭(C/C)复合材料,通过惯量试验机对其湿态摩擦磨损性能进行研究.结果表明:C/C复合材料的组织主要以粗糙层为主;随着热处理温度升高,复合材料的石墨化度增加,制动过程平稳,动、静摩擦系数升高,摩擦稳定性增加,在较高转速和制动压力下力矩曲线尾翘现象明显减弱;石墨化度较高试样的表面能够形成一层光滑、致密的润滑膜,从而降低其磨损率;所制备的C/C复合材料能够满足湿式摩擦材料的性能要求,并大幅度降低成本.     

Fe2O3/CNT催化湿法H2O2氧化苯酚

通过化学沉积法和热处理得到多壁碳纳米管负载Fe2O3催化剂 Fe2O3/CNT, Fe2O3的负载质量分数约为15.1%,XRD表征显示,负载的Fe2O3存在α和γ这2种晶型。考察了Fe2O3/CNT催化湿式H2O2氧化去除废水中苯酚催化性能,通过苯酚的去除率及反应过程中催化剂活性组分的溶出总量,研究了催化剂制备过程中添加聚乙烯醇对催化剂性能的影响。在苯酚和H2O2初始浓度分别为350和1 500 mg/L、催化剂投加量为1.0 g/L、温度80 ℃条件下,经过240 min的反应,苯酚去除率达100％,COD去除率为86.1％。     

Co掺杂ZnO薄膜的湿化学法制备及其光致发光光谱

采用湿化学法在Si衬底上生长了纳米棒结构的Co掺杂ZnO薄膜,并研究了掺杂浓度对生成样品结构和性能的影响.研究表明这种湿化学法成本低廉、收益高、重复性良好.样品的XRD结果表明掺杂的ZnO没有出现杂相.SEM结果表明掺杂样品是由ZnO纳米棒团簇结构组成,且团簇的密度随着Co掺杂浓度的增大而增大.薄膜的光致发光光谱结果表明Co掺杂导致薄膜的带隙发生红移,同时也证明了Co原子有效地进入了ZnO晶格.